EN
DE
FR
Servo MD250MW
Item No.: 1-00707
4,8-7,4 V | max. 73,55 N/cm | max. 0,13 Sek/60° | IP4X
Contents:
- 1x HiTEC Servo MD250MW
- Servo arm set (M-I25, R-ML25)
- Mounting hardware
Description
15mm extra class!
A servo of the standard size cannot always be installed, and the 12-13 mm servos are not strong and robust enough.
The solution, a 15mm servo that provides enough power and is still very light.
In addition to the well-known D-Series technology, which makes the servo fully programmable (details below),
this servo also comes with a magnetic encoder.
I.e. contactless position recording, absolutely wear-free, infinite service life and extremely precise!
What more do you need?
A full metal housing that only makes the servo heavier but not more robust, certainly not.
The MD250MW can be used from 4.8 to 8.4 volts and is therefore ideally suited for mid-range helis, but best for fixed-wing models where power and quick control response are required. This servo is preferably used as wing servos for large gliders.
And with ~ 9.1kgcm actuating force at 8.4 volts, it has a lot of power!
Features:
• Magnetic Encoder/ Hall Sensor
• Best servo travel resolution available on the market.
• Finest response
• programmable
• High force
• excellent holding power
• Metal gears
• 2 ball bearings MR106/MR85
• 25 serration for servo horn
Programmable features:
• Adjust end point (0°-180°), neutral (default ± 60°)
• Setting the direction of rotation (clockwise/counterclockwise)
• Setting the dead zone
• Setting the speed (default 100%))
• Set Soft Start (default 20%)
• Setting the fail-safe function
• Setting the overload protection (default off)
• Factory settings can be restored
A servo of the standard size cannot always be installed, and the 12-13 mm servos are not strong and robust enough.
The solution, a 15mm servo that provides enough power and is still very light.
In addition to the well-known D-Series technology, which makes the servo fully programmable (details below),
this servo also comes with a magnetic encoder.
I.e. contactless position recording, absolutely wear-free, infinite service life and extremely precise!
What more do you need?
A full metal housing that only makes the servo heavier but not more robust, certainly not.
The MD250MW can be used from 4.8 to 8.4 volts and is therefore ideally suited for mid-range helis, but best for fixed-wing models where power and quick control response are required. This servo is preferably used as wing servos for large gliders.
And with ~ 9.1kgcm actuating force at 8.4 volts, it has a lot of power!
Features:
• Magnetic Encoder/ Hall Sensor
• Best servo travel resolution available on the market.
• Finest response
• programmable
• High force
• excellent holding power
• Metal gears
• 2 ball bearings MR106/MR85
• 25 serration for servo horn
Programmable features:
• Adjust end point (0°-180°), neutral (default ± 60°)
• Setting the direction of rotation (clockwise/counterclockwise)
• Setting the dead zone
• Setting the speed (default 100%))
• Set Soft Start (default 20%)
• Setting the fail-safe function
• Setting the overload protection (default off)
• Factory settings can be restored
Technical data
Width (mm)
15,00
Motor Type
Cored Carbon Brush
Encoder
Magnetic Encoder
IP Protection Class
IP4X
Communication
PWM / TTL
Servo Type
Digital
Voltage max. (V)
7,40
Torque max. (kg/cm)
7,50
Setting Speed max. (sec/60 degrees)
0,13
Hitec Servo Series
MD-Series
Weight (gramm)
38,30
Horn Gear Spline
H25T (Ø6,0mm)
Length (mm)
35,40
Height (mm)
32,00
Voltage min. (V)
4,80
Torque min. (kg/cm)
4,90
Setting Speed min. (sec/60 degrees)
0,20
Angle Standard (degrees)
± 60°
Rotation Angle programmable (degrees)
320°
Multi Turn
not possible
Contniuos Rotation
No
Current Draw at idle (mA)
40
Current Draw max. (mA)
1600
Torque min. (N/cm)
48,05
Torque max. (N/cm)
73,55
Housing
Engineering Plastic
Connector
Hitec 3 Pin (Uni)
Gearing (characteristic)
Steel
Optional Accessories
Spare Parts
Alternate articles